RLC Series Circuits with AC, Alternating-Current Circuits | University Physics Volume 2

Learning objectives

By the end of this section, you will be able to:

Describe how the current varies in a resistor, a capacitor, and an inductor while in series with an ac power source
Use phasors to understand the phase angle of a resistor, capacitor, and inductor ac circuit and to understand what that phase angle means
Calculate the impedance of a circuit

The ac circuit shown in CNX_UPhysics_32_03_acrlc, called an RLC series circuit, is a series combination of a resistor, capacitor, and inductor connected across an ac source. It produces an emf of

v (t) = V_{0} sin ω t .

View original figure (external; image not reproduced in this text edition)

Original figure description: Figure a shows a circuit with an AC voltage source connected to a resistor, a capacitor and an inductor in series. The source is labeled V0 sine omega t. Figure b shows sine waves of AC voltage and current on the same graph. Voltage has a greater amplitude than current and its maximum value is marked V0 on the y axis. The maximum value of current is marked I0. The two curves have the same wavelength but are out of phase. The voltage curve is labeled V parentheses t parentheses equal to V0 sine omega t. The current curve is labeled I parentheses t parentheses equal to I0 sine parentheses omega t minus phi parentheses.

(a) An RLC series circuit. (b) A comparison of the generator output voltage and the current. The value of the phase difference

ϕ

depends on the values of R, C, and L.

Since the elements are in series, the same current flows through each element at all points in time. The relative phase between the current and the emf is not obvious when all three elements are present. Consequently, we represent the current by the general expression

i (t) = I_{0} sin (ω t - ϕ),

where $I_{0}$ is the current amplitude and $ϕ$ is the phase angle between the current and the applied voltage. The phase angle is thus the amount by which the voltage and current are out of phase with each other in a circuit. Our task is to find $I_{0} and ϕ .$

A phasor diagram involving $i (t), v_{R} (t), v_{C} (t), and v_{L} (t)$ is helpful for analyzing the circuit. As shown in CNX_UPhysics_32_03_phasorrlc, the phasor representing $v_{R} (t)$ points in the same direction as the phasor for $i (t);$ its amplitude is $V_{R} = I_{0} R .$ The $v_{C} (t)$ phasor lags the i(t) phasor by $π / 2$ rad and has the amplitude $V_{C} = I_{0} X_{C} .$ The phasor for $v_{L} (t)$ leads the i(t) phasor by $π / 2$ rad and has the amplitude $V_{L} = I_{0} X_{L} .$

View original figure (external; image not reproduced in this text edition)

Original figure description: Figure shows the coordinate axes, with four arrows starting from the origin. Arrow V subscripts R points up and right, making an angle omega t minus phi with the x axis. Its y intercept is V subscript R parentheses t parentheses. Arrow I0 is along arrow V subscript R, but shorter than it. Arrow V subscript L points up and left and is perpendicular to V subscript R. It makes a y intercept V subscript L parentheses t parentheses. Arrow V subscript C points down and right. It is perpendicular to V subscript R. It makes a y intercept V subscript C parentheses t parentheses. Three arrows labeled omega are each perpendicular to V subscript R, V subscript L and V subscript C, shown near their tips.

The phasor diagram for the RLC series circuit of CNX_UPhysics_32_03_acrlc.

At any instant, the voltage across the RLC combination is $v_{R} (t) + v_{L} (t) + v_{C} (t) = v (t),$ the emf of the source. Since a component of a sum of vectors is the sum of the components of the individual vectors—for example, ${(A + B)}_{y} = A_{y} + B_{y}$ —the projection of the vector sum of phasors onto the vertical axis is the sum of the vertical projections of the individual phasors. Hence, if we add vectorially the phasors representing $v_{R} (t), v_{L} (t), and v_{C} (t)$ and then find the projection of the resultant onto the vertical axis, we obtain

v_{R} (t) + v_{L} (t) + v_{C} (t) = v (t) = V_{0} sin ω t .

The vector sum of the phasors is shown in CNX_UPhysics_32_03_vectorsum. The resultant phasor has an amplitude $V_{0}$ and is directed at an angle $ϕ$ with respect to the $v_{R} (t),$ or $i (t)$ , phasor. The projection of this resultant phasor onto the vertical axis is $v (t) = V_{0} sin ω t .$ We can easily determine the unknown quantities $I_{0}$ and $ϕ$ from the geometry of the phasor diagram. For the phase angle,

ϕ = {tan}^{−1} \frac{V_{L} - V_{C}}{V_{R}} = {tan}^{−1} \frac{I_{0} X_{L} - I_{0} X_{C}}{I_{0} R},

and after cancellation of $I_{0},$ this becomes

Furthermore, from the Pythagorean theorem,

V_{0} = \sqrt{V_{R}^{2} + {(V_{L} - V_{C})}^{2}} = \sqrt{{(I_{0} R)}^{2} + {(I_{0} X_{L} - I_{0} X_{C})}^{2}} = I_{0} \sqrt{R^{2} + {(X_{L} - X_{C})}^{2}} .

View original figure (external; image not reproduced in this text edition)

Original figure description: Three arrows start from the origin on the coordinate axis. Arrow V subscript R points up and right, making an angle omega t minus phi with the x axis. Arrow V0 points up and right, making an angle omega t with the x axis. It makes an angle phi with the arrow V subscript R. It makes a y intercept labeled V0 sine omega t. The third arrow is labeled V subscript L minus V subscript C. It points up and left and is perpendicular to arrow V subscript R. Dotted lines indicate that the rectangle formed with its longer side being V subscript R and shorter side being V subscript L minus V subscript C, would have the arrow V0 as a diagonal. An arrow labeled omega is shown near the tip of V subscript R, perpendicular to it.

The resultant of the phasors for

v_{L} (t)

v_{C} (t)

, and

v_{R} (t)

is equal to the phasor for

v (t) = V_{0} sin ω t .

The i(t) phasor (not shown) is aligned with the

v_{R} (t)

phasor.

The current amplitude is therefore the ac version of Ohm’s law:

where

is known as the impedance of the circuit. Its unit is the ohm, and it is the ac analog to resistance in a dc circuit, which measures the combined effect of resistance, capacitive reactance, and inductive reactance (CNX_UPhysics_32_03_powerlines).

View original figure (external; image not reproduced in this text edition)

Original figure description: Photograph of power capacitors at a power station.

Power capacitors are used to balance the impedance of the effective inductance in transmission lines.

The RLC circuit is analogous to the wheel of a car driven over a corrugated road (CNX_UPhysics_32_03_Shock). The regularly spaced bumps in the road drive the wheel up and down; in the same way, a voltage source increases and decreases. The shock absorber acts like the resistance of the RLC circuit, damping and limiting the amplitude of the oscillation. Energy within the wheel system goes back and forth between kinetic and potential energy stored in the car spring, analogous to the shift between a maximum current, with energy stored in an inductor, and no current, with energy stored in the electric field of a capacitor. The amplitude of the wheel’s motion is at a maximum if the bumps in the road are hit at the resonant frequency, which we describe in more detail in Resonance in an AC Circuit.

View original figure (external; image not reproduced in this text edition)

Original figure description: Figure shows one wheel of a car. Arrows show the up-down motion of its shock absorber spring.

On a car, the shock absorber damps motion and dissipates energy. This is much like the resistance in an RLC circuit. The mass and spring determine the resonant frequency.

AC Circuits

To analyze an ac circuit containing resistors, capacitors, and inductors, it is helpful to think of each device’s reactance and find the equivalent reactance using the rules we used for equivalent resistance in the past. Phasors are a great method to determine whether the emf of the circuit has positive or negative phase (namely, leads or lags other values). A mnemonic device of “ELI the ICE man” is sometimes used to remember that the emf (E) leads the current (I) in an inductor (L) and the current (I) leads the emf (E) in a capacitor (C).

Use the following steps to determine the emf of the circuit by phasors:

Draw the phasors for voltage across each device: resistor, capacitor, and inductor, including the phase angle in the circuit.
If there is both a capacitor and an inductor, find the net voltage from these two phasors, since they are antiparallel.
Find the equivalent phasor from the phasor in step 2 and the resistor’s phasor using trigonometry or components of the phasors. The equivalent phasor found is the emf of the circuit.

An RLC Series Circuit

The output of an ac generator connected to an RLC series combination has a frequency of 200 Hz and an amplitude of 0.100 V. If

R = 4.00 Ω,

L = 3.00 \times 10^{−3} H,

and

C = 8.00 \times 10^{−4} F,

what are (a) the capacitive reactance, (b) the inductive reactance, (c) the impedance, (d) the current amplitude, and (e) the phase difference between the current and the emf of the generator?

Strategy

The reactances and impedance in (a)–(c) are found by substitutions into fs-id1172101611081, fs-id1172101883508, and fs-id1172101939380, respectively. The current amplitude is calculated from the peak voltage and the impedance. The phase difference between the current and the emf is calculated by the inverse tangent of the difference between the reactances divided by the resistance.

Solution

From fs-id1172101611081, the capacitive reactance is $X_{C} = \frac{1}{ω C} = \frac{1}{2 π (200 Hz) (8.00 \times 10^{−4} F)} = 0.995 Ω .$
From fs-id1172101883508, the inductive reactance is $X_{L} = ω L = 2 π (200 Hz) (3.00 \times 10^{−3} H) = 3.77 Ω .$
Substituting the values of R, $X_{C}$ , and $X_{L}$ into fs-id1172101939380, we obtain for the impedance $Z = \sqrt{{(4.00 Ω)}^{2} + {(3.77 Ω - 0.995 Ω)}^{2}} = 4.87 Ω .$
The current amplitude is $I_{0} = \frac{V_{0}}{Z} = \frac{0.100 V}{4.87 Ω} = 2.05 \times 10^{−2} A .$
From fs-id1172101939335, the phase difference between the current and the emf is $ϕ = {tan}^{−1} \frac{X_{L} - X_{C}}{R} = {tan}^{−1} \frac{2.77 Ω}{4.00 Ω} = 0.607 rad .$

Significance

The phase angle is positive because the reactance of the inductor is larger than the reactance of the capacitor.

Summary

An RLC series circuit is a resistor, capacitor, and inductor series combination across an ac source.
The same current flows through each element of an RLC series circuit at all points in time.
The counterpart of resistance in a dc circuit is impedance, which measures the combined effect of resistors, capacitors, and inductors. The maximum current is defined by the ac version of Ohm’s law.
Impedance has units of ohms and is found using the resistance, the capacitive reactance, and the inductive reactance.

Conceptual Questions

In an RLC series circuit, can the voltage measured across the capacitor be greater than the voltage of the source? Answer the same question for the voltage across the inductor.

yes for both

Problems

What is the impedance of a series combination of a $50 -Ω$ resistor, a $5.0 - μ F$ capacitor, and a $10 - μ F$ capacitor at a frequency of 2.0 kHz?

A resistor and capacitor are connected in series across an ac generator. The emf of the generator is given by $v (t) = V_{0} cos ω t,$ where $V_{0} = 120 V,$ $ω = 120 π rad/s,$ $R = 400 Ω$ , and $C = 4.0 μ F$ . (a) What is the impedance of the circuit? (b) What is the amplitude of the current through the resistor? (c) Write an expression for the current through the resistor. (d) Write expressions representing the voltages across the resistor and across the capacitor.

a. $770 Ω$ ; b. 0.16 A; c. $I = (0.16 A) cos (120 π t - 0.33 π)$ ; d. $v_{R} = 62 cos (120 π t - 0.33 π)$ ; $v_{C} = 103 cos (120 π t - 0.83 π)$

A resistor and inductor are connected in series across an ac generator. The emf of the generator is given by $v (t) = V_{0} cos ω t,$ where $V_{0} = 120 V$ and $ω = 120 π rad/s;$ also, $R = 400 Ω$ and $L = 1.5 H .$ (a) What is the impedance of the circuit? (b) What is the amplitude of the current through the resistor? (c) Write an expression for the current through the resistor. (d) Write expressions representing the voltages across the resistor and across the inductor.

In an RLC series circuit, the voltage amplitude and frequency of the source are 100 V and 500 Hz, respectively, an $R = 500 Ω,$ $L = 0.20 H,$ and $C = 2.0 μ F .$ (a) What is the impedance of the circuit? (b) What is the amplitude of the current from the source? (c) If the emf of the source is given by $v (t) = (100 V) sin 1000 π t$ , how does the current vary with time? (d) Repeat the calculations with C changed to $0.20 μ F .$

a. $690 Ω$ ; b. 0.15 A; c. $I = (0.15 A) sin (1000 π t - 0.753)$ ; d. $1100 Ω$ , 0.092 A, $I = (0.092 A) sin (1000 π t + 1.09)$

An RLC series circuit with $R = 600 Ω$ , $L = 30 mH,$ and $C = 0.050 μ F$ is driven by an ac source whose frequency and voltage amplitude are 500 Hz and 50 V, respectively. (a) What is the impedance of the circuit? (b) What is the amplitude of the current in the circuit? (c) What is the phase angle between the emf of the source and the current?

For the circuit shown below, what are (a) the total impedance and (b) the phase angle between the current and the emf? (c) Write an expression for $i (t) .$

View original figure (external; image not reproduced in this text edition)

Original figure description: Figure shows a circuit with a voltage source 170 V, sine 120 pi t, a resistor of 5 ohm, a capacitor of 400 microfarad and an inductor of 25 milihenry all connected in series.

a. $5.7 Ω$ ; b. $29 °$ ; c. $I = (30. A) cos (120 π t + 0.51)$

Glossary

impedance: ac analog to resistance in a dc circuit, which measures the combined effect of resistance, capacitive reactance, and inductive reactance
phase angle: amount by which the voltage and current are out of phase with each other in a circuit

Attribution. University Physics Volume 2, OpenStax, Rice University, and the contributing authors credited in the book. Licensed under Creative Commons Attribution 4.0 International. Source revision db44eb99e9 of openstax/osbooks-university-physics-bundle (2026-02-02). CC BY 4.0. Original source ↗. Text edition of a pinned CC BY 4.0 source revision of the OpenStax book, converted from CNXML by the EvidenceHelix importer. Original prose, learning objectives, tables, exercises, glossary and captions are preserved; images are not copied (figures link to the original source and keep their credits). No new content was added. Later revisions of this book can carry different licence terms and are not used.